| Fasteners | 3x6x0.5 Shim Washer | 50 | |
| M2 Nut | 55 | |
| M3 Nut | 140 | |
| M2x6 SHCS | 70 | |
| M2x6 FHCS | 10 | |
| M2x8 SHCS | 10 | |
| M3x6 BHCS | 40 | |
| M3x8 BHCS | 115 | |
| M3x8 FHCS | 5 | |
| M3x10 BHCS | 50 | |
| M3x12 BHCS | 25 | |
| M3x16 BHCS | 10 | |
| M3x25 BHCS | 10 | |
| M3x30 BHCS | 10 | |
| M3x35 BHCS | 30 | |
| M3x40 BHCS | 10 | |
| M2x10 Self Tapping Screws for Plastic | 30 | |
| M3 Brass heatstake inserts - short M3x5x4 | 50 | |
| Makerbeam XL M3 t-nut | 2 | |
| Frame | Makerbeam XL 15x15 200mm | 16 | |
| Makerbeam XL 15x15 100mm | 3 | |
| Extrusion Tophat Frame | Makerbeam XL 15x15 200mm | 4 | |
| Makerbeam XL 15x15 80-100mm | 4 | |
| Electronics | Meanwell LRS-150-24 | 1 | |
| Bigtreetech SKR Pico | 1 | |
| Raspberry Pi 3 | 1 | |
| MicroSD Card | 1 | |
| NEMA14 Stepper Motor 40Ncm | 2 | |
| NEMA17 Stepper Motor w/ integrated lead screw | 1 | |
| 3010 blower fans 24V | 2 | |
| 3010 axial fan 24V | 2 | |
| Omron Mouse Button - Micro Switch | 2 | |
| C13 Power Cord | 1 | |
| IEC320 C14 inlet | 1 | |
| Hotend | 1 | |
| 24V Heater Cartridge | 1 | |
| Hotend thermistor | 1 | |
| V0-Display | 1 | |
| ECAS04 Bowden Fitting | 1 | |
| 3M 5952 VHB tape | 1 | |
| Cables | Insulated Crimp Receptical | 4 | |
| High Flex Wire 22gauge 100ft | 1 | |
| High Flex Wire 20gauge 10ft | 1 | |
| Wire 18gauge 10ft | 1 | |
| Thermal Fuse 150C | 1 | |
| JST connectors (2pin 3pin 4pin) | ? | |
| Microfit3 Dual Row (10circuits) Male & Female | 1 | |
| 7mm x 7mm cable chain (less than 1/2 meter) | 1 | |
| Nylon Cable Ties (1.8mm wide or smaller) | 50 | |
| Motion | F623-RS Bearing | 24 | |
| MGN7H Linear Rail with Carriage - 150mm | 5 | |
| GT2 20T (5mm ID 6mm W) | 2 | |
| GT2 Open Belt (6mm W) - 3000mm | 1 | |
| T8x8 Anti-backlash Flange Nut | 1 | |
| Buildplate | MIC6 1/4” Plate - 120x120mm | 1 | |
| Silicone DC 24V Heater 100x100mm 60W | 1 | |
| PEI + 3M 468MP (200MP) | 1 | |
| yellow die springs 8x4x20mm | 3 | |
| Magnetic sheet for spring steel plate 120x120 | 1 | Optional |
| Spring Steel Flex Buildplate 120x120mm | 1 | Optional |
| Panels | Acrylic Sheet Clear (sides) - 212x230x3mm | 2 | |
| Acrylic Sheet Clear (door) - 212x239x3mm | 1 | |
| Upper Rear Panel 212x63x3mm | 1 | |
| Lower Rear Panel 212x185x3mm | 1 | |
| Deck Panel 3mm thick (See DXF) | 1 | |
| Motor Panel 3mm thick (See DXF) | 1 | |
| Bottom Panel 3mm thick (See DXF) | 1 | |
| Mid Panel 3mm thick (See DXF) | 1 | |
| Bowden | Bowden Fitting | 2 | |
| Bowden Tube 4x2mm - 1m | 1 | |
| Misc. | Little Rubber Feet | 4 | |
| Bowden Tube 4x3mm - 1m | 1 | |
| Medium Strength Thread Locker | 1 | |
| 6mm x 3mm Round Neodymium Magnets | 8 | |
| Extrusion Tophat Panels | Top Panel 212x212mm | 1 | |
| Side Panels 212x(71-91)mm | 4 | |
| Extruder | NEMA14 36mm pancake Motor with 10 tooth gear | 1 | |
| Bondtech BMG Extruder Kit | 1 | |
| MR85 Bearing | 3 | |
